![\"image\"](\"http:\/\/lisby.dk\/wordpress\/wp-content\/uploads\/2016\/10\/image-40.jpeg\")
<\/a><\/figure><\/div>\n\n\n<\/p>\n\n\n\n
Home again, the new train had to go on my layout. Next time, I must listen more caarefully to other peoples bad experience. It is work half-done from Heljan. And my train is second generation, which is supposed to be much better than first generation.<\/p>\n\n\n\n
An IC3 train consists of 3 wagons (see http:\/\/www.jernbanen.dk\/lyntog.php?typenr=5&n=dsb-ic3-litra-mfa-mfb<\/a>). Two motorized wagons – one at each end – and a non-motorized wagon in-between that actually shares boogies with the two end-wagons.<\/p>\n\n\n\n Heljan has chosen to make the train the opposite way, i.e. it is the middle wagon that it motorized. The motor is connected to the common boogies via drive shafts. The collector shoe is placed underneath one of the end-wagons.<\/p>\n\n\n\n Even though the motor is driving the shared boogies, these boogies are not directly attached to the wagon. Instead the wagons are just loosely placed above the boogies so that some 2mm long plastic plugs are supposed to keep the entire train from falling apart. And that obviously doen’t work.<\/p>\n\n\n <\/p>\n\n\n\n It is a strange train that Heljan has produced. I forgot to keep the middle wagon and the two boogies tightly together with my hands when I lifted it from the track. And that warning in the manual seems to be meant seriously. The reult was that one of the boogies shifted a few millimeters with the result that one of the drive shafts fell out. And it was not easy to get back into place.<\/p>\n\n\n\n In addition, one of the small plastic things that is guiding wires between the wagons and that I also suppose shall look like the connection between the wagons in the real world also fell off. That is by the way done by sliding it carefully horizontally into some grooves where it fits right where the drive shaft is stuck into the boogie.<\/p>\n\n\n <\/p>\n\n\n\n The problem right now is that the wagon that is equipped with a collector shoe weighs almost nothing whereas the middle wagon is pretty heavy. Consequently, the collector shoe wagon de-rails each time I push it ever so cautiously across a particular switch.<\/p>\n\n\n\n I don’t know why it doesn’t go wrong in all switches. But I guess I am going to make it work once I realize how to open up the wagon without breaking it so that I can add weight to it in order to keep the collector shoe boogie into the track at all times.<\/p>\n\n\n\n Or is it the distance between the wheels that is the problem? I have read that there must be between 14,1 and 14,2 mm between the wheels and that several people have experienced that that is not the case on their HEljan IC3. I just don\u2019t think it looks as if that is the problem. When the train is standing on a straight piece of track, there is the same kind of tolerance felt when I cautiously rocks the train from side to side as there is with my good BR216 locomotive.<\/p>\n\n\n\n But I’d better check with a vernier caliper. The standard is here: http:\/\/www.morop.eu\/de\/normes\/nem340_d.pdf<\/a> and there is a blog about the specific Heljan problem here: http:\/\/dk.fritid.jernbaner.model.narkive.com\/Zwbkd9x1\/heljan-ic3-konsekvent-afsporing-i-skiftespor<\/a>. It sounds as if the measure should be more like 14,0 – 14,1 mm.<\/p>\n\n\n\n Another problem is that the train will not start until it gets at least 30% throttle. I must find out if that is due to a bad engine or if some CV values in the decoder need adjusment.<\/p>\n\n\n\n There is a Youtube video showing a train where the motor has been changed to one from Mashima. But there is no explanation about why or how: http:\/\/youtu.be\/njH1O_IwqjM<\/a>. From the very few comments, it just sounds as if the original motor became defect and they just found a new similar motor.<\/p>\n\n\n\n It may be the PID regulation in the decoder that has been set up foolishly. It might also be the wheel distance that makes it hard for the motor to haul the train. Or just basically a bad design of the train. I intend to try to fiddle with the PID regulation at some point in time.<\/p>\n\n\n\n An additional problem that has not emerged yet, but which just seems to wait to emerge, is broken wires. I wonder why Heljan is using stiff wires between wagons and for the collector shoe etc.? I would have chosen the soft kind that are more durable to bends and twists. Well. That will have to wait until they actually start breaking.<\/p>\n\n\n\n So at the moment, it is not a good train. But it looks nice (even though the details are not particularly fine – for example no yellow stripe to indicate first class, no interior, handles etc. are non-existent etc.). So worst case, the train might just become a decorative element on my layout. And then maybe from time to time, I can run it manually for a little trip. As it is, there is no way to let it run under computer control.<\/p>\n\n\n\n The distance between the wheels is a bit to much – about 14,2 mm. For comparison, my BR216 is 14,0 mm. I have seen that Togcenter Gentofte is selling wheels for Heljan B-wagons, that will make those wagons run on M\u00e4rklin track. And Togcenter Gentofte thinks those wheels might also help the IC3 train to run better, although probably not perfect.<\/p>\n\n\n\n But I can only use such wheels on the boogies where the motor is not driving the train. So if I in any instance need to adjust the driving wheels, I might as well adjust all of them. Special tools even exist for that kind of job: https:\/\/www.fohrmann.com\/radsatz-richtgerat.html<\/a> But I think it will turn into a major operation to dismount all whells, adjust them and put them back on the train again.<\/p>\n\n\n\n So I will try out the other good advice from Togcenter Gentofte: Adding a little weight. And he underlined “a little”.<\/p>\n\n\n\n A third thing he told me was how to take the top of the end wagons: Pull out the lower corners of the white part nearest to the middle wagon cautiosly. Then push the white part towards the end of the train.<\/p>\n\n\n\n I had some trouble with finding out where to add weight and how much to add. I was driving back and forth across the switches with the upper part dangling on top. But that doesn’t work, since that dangling upper part makes the train much more unstable. That gives an idea about how sensitive this is to even a few grams that are badly distributed.<\/p>\n\n\n\n Having put the top of the wagon almost in its correct position, I slowly and by hand pushed the train over the offending switch. I observed that it was the end facing the center wagon that tilted a bit as the collector shoe passed the switch. I then placed a 13 mm bolt in that end of each of the two non-motorized wagons. \u00c9t voila: No more de-railing.<\/p>\n\n\n I do however still not dare to drive fast (only about 75 km\/h in model speed). My layout is placed more than a meter above floor level and the train will definitely not survive a plunge into the deep. It would disintegrate to a degree that I would not have any idea of which shards I should glue to which. So my plan going forward is to glue the bolts in place and then put the top of the wagons into place and do some test driving.<\/p>\n\n\n\n The train is however still not approved for anything else than manual driving below the mentioned speed.<\/p>\n\n\n Do I regret my purchase? No. That train belongs to my layout. And it is fun to have a train that I actually often ride in the real world. But I wish that it had been produced by a company such as Roco or M\u00e4rklin. In that case, it would have been much more reliable.<\/p>\n\n\n\n I re-iterated the test driving from yesterday. Still without problems. I then glued the bolts and took the pictures shown above. I hope the glue is strong enough, even though it is not epoxy. But we will see.<\/p>\n\n\n\n If the bolts seem to sit tight tomorrow, I will assemble the IC3 train and put it aside so that I can get on with building my layout, adding signals, rebuilding my old M\u00e4rklin Santa Fe and then my Lima MR for digital operation.<\/p>\n\n\n\n It has been a sad period regarding the IC3 train. What a piece of shit.<\/p>\n\n\n\n The decoder is from Lenz. But not just any decoder from Lenz. It is their very first decoder. And it has no capabilities whatsoever to regulate the motor. That is definitely a huge part of the explanation why the train either doesn’t start or at least stops in the very first switch or curve unless it travels with at least 50 km\/h.<\/p>\n\n\n\n And even though the bolt trick made it possible to pass switches, there is another problem: The drive shafts are falling off each time the train has been driving a couple of rounds on my tiny oval. And it is still very difficult to put back into place.<\/p>\n\n\n\n The problem is that the train is simply not assembled. The wagons are just placed loosely above the boogies. I have complained to togdillen and he has sent me some plastic thingies that I don’t know what I shall use for. Latest, he has asked me to come to his shop in Vanl\u00f8se, which is 25 km away, so they can have a look at the train.<\/p>\n\n\n\n I have decided that now it is enough. That train is simply not designed in the right way. It will never run. I will go to Togdillen and get my money back. Or maybe I will find another type of locomotive from an other vendor.<\/p>\n\n\n\n Today is Saturday, and I got time to go to Togdillen. That was what I call good service. He pretended not to hear that I wanted my money back. Maybe he actually did not hear it? Or maybe he just understood it as I would like to return the train and get another one of the same kind instead? At least that was what happened.<\/p>\n\n\n\n And it was an entirely different train. It looks like a new train. It doesn’t have this yellow\/brownish glow from exposure to sunlight that the first one had. And the boogies are actually screwed to the middle wagon.<\/p>\n\n\n\n In fact I got the impression that he was kind of sorry to have sold a used train, that didn’t work, but falls apart. He said something like he didn’t understand it. Whatever “it” means?<\/p>\n\n\n\n I also told him about the problems with driving slowly. And immediately he fetched an ESU LokPilot 4.0 and mounted it in the train. Yes!!! Just he cure I had also thought of. Now just for the price of nothing.<\/p>\n\n\n\n Back home again, the train had to go for a ride. Onto the layout. Sloooowly round one way. It worked!!!!!!! Slowly the other way, It was able to do that too. Then we make it harder where the first train de-railed consequently. And here the pleasure stops. The new train de-rails too. Al of I sudden, I feel an urge to say a lot of less nice words very fast. I have not tried the hard spot in the opposite direction yet. I got so sad that I sat down and wrote this in my diary instead.<\/p>\n\n\n\n On the other hand, now I know the bolt trick. Maybe I should try that again? Maybe with a little less weight in the beginning? Or maybe this time, I should do the wheel adjustment instead?<\/p>\n\n\n\n At least, I sense there is basis for success this time.<\/p>\n\n\n\n By now I have tried the hard spot in both directions. Several times with different speeds (but no high speeds). Nu mishaps. But the train stil kind of wrigles its way across the switch. And there is also a tendency for the wheels on the axle closest to the center wagon to lift up. Both symptoms seem to point to a need for more weight – i.e. the bolt trick.<\/p>\n\n\n\n But that will have to wait. Until further, I will only feel hapiness for owning an IC3 train that is able to run. And then carry on with building S88N modules and to make the computer control work.<\/p>\n\n\n\n The following pictures show the first train.<\/p>\n\n\n\n The decoder is from Lenz. The very oldest one without motor control and all in all a miserable piece of electronics. The new train has the best of the best instead, i.e. an ESU LokPilot 4.0:<\/p>\n\n\n <\/p>\n\n\n All three wagons are only loosely put on top of the boogies. On the new train, the boogies are screwed onto the middle wagon, which prohibits the drive shafts etc. from falling off: I have placed a bolt to add weight in order for the train to be able to pass switches. I have not done so on my new train, since it is not absolutely necessary, even though also the new train has symptoms indicating that it might still be a good idea to add weight: The motor is placed in the center wagon and hauls the train via two drive shafts – one for each boogie. That is the same in the new train, but with the difference that the drive shafts do not fall off repeatedly:<\/p>\n\n\n A look inside the wagon where the collector shoe is placed underneath. As it can be seen, numerous wires are lead through the train. They are the stiff kind that may break after relatively little time. But then I am going to have to solder new softer wires instead. Also note the relatively little realism in the model: No interior, red windows, not much detail, not even the yellow stripe to indicate first class. And that is even though other Heljan models are very nice:<\/p>\n\n\n A look at the entire train:<\/p>\n\n\n A closer look at the poor way to lead the wires between wagons:<\/p>\n\n\n\n After more years where the IC3 train has just been standing on a shelf, I have re-iterated the test driving. The result was that now the drive shafts drops out of their bearings after a few meters.<\/p>\n\n\n\n But at Hobbymessen, the very sae sales person that sold the train to me originally asked me to give it back for repair. As he said, they only want satisfied customers.<\/p>\n\n\n\n I have done so, and they have obtained another satisfied customer.<\/p>\n\n\n\n They have exchanged the unstable plastic drive shafts with metal ones. They are somewhat noisy. And the train does not run as well as for example a M\u00e4rklin or a Roco product would. But as long as I keep it out of narrow S-curves, it works.<\/p>\n\n\n\n I can only recommend Togdillen. They can do magic. But only buy Heljan products if you can live with \u201csecond-best\u201d.<\/p>\n\n\n\n Jeg havde som s\u00e5 mange andre h\u00e5bet, at Mck ville konstruere et IC3 tog. Men for en m\u00e5nedstid eller to siden annoncerede de, at de havde unders\u00f8gt \u00f8konomien i s\u00e5dan et projekt, og efterf\u00f8lgende droppet ideen.<\/p>\n\n\n\n I mellemtiden har Heljan udgivet en ny og forbedret serie, som jeg ikke kunne n\u00e6re mig for at k\u00f8be. Det k\u00f8rer ikke bedre end mit gamle IC3 tog. Tv\u00e6rtimod. Det afsporer hele tiden. Men indtil videre har det ikke mistet kardaner eller lignende.<\/p>\n\n\n <\/p>\n\n\n Toget er visuelt flottere end det gamle. Mit tog er i nyeste bemaling med r\u00f8de d\u00f8rmarkeringer og r\u00f8dt DSB logo:Udover bemaling m.v. – incl. den gule stribe p\u00e5 1. klasse, som jeg savnede p\u00e5 det gamle tog, s\u00e5 er hele fronten incl. sneploven nu lavet af gummi. Jeg ved ikke rigtigt, om det er en forbedring eller det modsatte. D\u00f8m selv. Jeg synes faktisk, at sneploven ser mere rigtig ud p\u00e5 det gamle tog.<\/p>\n\n\n\n Og bem\u00e6rk, at h\u00e5ndlisterne ved lokof\u00f8rernes d\u00f8re nu er af metal i stedet for bare at v\u00e6re en del af plast-st\u00f8bningen.<\/p>\n\n\n S\u00e5 kommer vi til teknikken og k\u00f8reegenskaberne. Det f\u00f8rste man m\u00f8der, n\u00e5r man tager l\u00e5get af den i \u00f8vrigt ret fine kasse, er en meget kortfattet brugsanvisning, der angiver, at man skal skille midtervognen ad og fjerne noget tape og eventuelt genmontere den stift, som tapen angiveligt skulle holde fast. S\u00e5 det f\u00f8rste jeg gjorde var derfor at hive toppen af midtervognen:<\/p>\n\n\n\n Jeg fik aldrig \u00f8je p\u00e5 hverken tape eller stift. Men jeg konstaterede, at der sidder en skrue ned i hver boogie for at holde dem fast. Det kan t\u00e6nkes, at det er en af forbedringerne, at den skrue sidder der ab fabrik i stedet for at forhandleren eller kunden har skullet tilf\u00f8je skruerne i den forrige udgave. Og vejledningen er m\u00e5ske ikke \u00e6ndret tilsvarende?<\/p>\n\n\n\n En anden forbedring, jeg kunne konstatere, er, at kardanerne er lavet af metal. Dvs. akslerne er. Selve kardanleddet ser stadigv\u00e6k ud til at v\u00e6re plastik.<\/p>\n\n\n\n Den mest v\u00e6sentlige forbedring er dog dekoderen. Det nye tog er udstyret med en ESU LokPilot 4. Jeg ved ikke, hvorfor Heljan har valgt micro udgaven. Der er fint plads til den normale. Men de sparer m\u00e5ske et par \u00f8rer? Og dekoderen (dvs. motorstyringen) fungerer fint.<\/p>\n\n\n\n Og s\u00e5 kommer vi til k\u00f8reegenskaberne eller rettere manglen p\u00e5 k\u00f8reegenskaber. Toget kan for s\u00e5 vidt godt k\u00f8re. Og der er ingen grimme lyde. Problemet er, at toget ikke kan dreje uden at afspore. I vejledningen st\u00e5r der, at toget skal kunne klare radier ned til 350 mm. Det kan det bare ikke. Den afsporer i mine 360 mm kurver. M\u00e5ske fordi samtlige mine skinner inklusive kurverne udg\u00f8r stigninger p\u00e5 op til flere procent. Men ogs\u00e5 i S-kurver \/ mine sporskifter g\u00e5r det helt galt. Toget hopper, vrikker og afsporer. Dvs. endevognene afsporer. Dels i ende-boogierne og dels p\u00e5 den aksel af Jacobs boogierne, der er under endevognene.<\/p>\n\n\n F\u00f8rste fors\u00f8g p\u00e5 udbedring er at l\u00e6gge en bolt i hver endevogn. F\u00f8rst i vognen uden sl\u00e6besko. Den fik en bolt p\u00e5 14 gram:<\/p>\n\n\n\n Bolten satte jeg fast med dobbeltkl\u00e6bende tape. Bem\u00e6rk v\u00e6gtklodsen, som Heljan allerede har anbragt. De har alts\u00e5 fors\u00f8gt. Bare ikke nok. Denne v\u00e6gtklods er i \u00f8vrigt ikke noget nyt. Jeg ser til egen overraskelse, at der ogs\u00e5 er v\u00e6gtklodser p\u00e5 mine egne billeder ovenfor af det gamle tog.<\/p>\n\n\n Dern\u00e6st vognen med sl\u00e6besko. Jeg t\u00e6nkte, at her skulle der mere v\u00e6gt til for at holde sl\u00e6beskoen i sporet, s\u00e5 jeg havde forberedt en l\u00e6ngere bolt med to m\u00f8trikker. Men her ventede en \u00e6gte nyhed, idet der allerede var tilf\u00f8jet endnu mere v\u00e6gt:<\/p>\n\n\n Det bet\u00f8d, at der ikke var plads til m\u00f8trikkerne, s\u00e5 jeg n\u00f8jedes med bolten p\u00e5 21 gram:<\/p>\n\n\n\n Med disse to bolte p\u00e5 plads kan toget faktisk k\u00f8re. Bedst hvis den f\u00e5r lov at k\u00f8re \u201cbagl\u00e6ns\u201d, dvs. s\u00e5dan at vognen med sl\u00e6besko skubbes foran midtervognen.<\/p>\n\n\n\n M\u00e5ske skal toget bare k\u00f8res til nu. Det vil jeg i hvert fald fors\u00f8ge. Det vrikker stadigv\u00e6k igennem sporskifterne. Men det ser umiddelbart ud til at kunne k\u00f8re rundt p\u00e5 den del af min bane, der best\u00e5r af en blanding af R1 og R2 skinner og kurve-sporskifter. Og det endda selvom jeg lader toget k\u00f8re ind p\u00e5 et vigespor, hvor det skal dreje i modsat retning. Og b\u00e5de fremad og med toget i dets foretrukne \u201cbakgear\u201d.<\/p>\n\n\n Men afsporinger sker stadigv\u00e6k for hyppigt. Is\u00e6r ved boogien med sl\u00e6besko, n\u00e5r denne vogn tr\u00e6kkes bagerst, som Heljan tilsyneladende mener det skal v\u00e6re. Jeg har tilf\u00f8jet 14 gram mere s\u00e5 langt henne ved sl\u00e6beskoen, som jeg kunne:<\/p>\n\n\n\n Som det anes p\u00e5 billedet, har Heljan ogs\u00e5 gjort deres indsats her. Og toget afsporer da ogs\u00e5 stadigv\u00e6k det samme sted. M\u00e5ske skal sl\u00e6beskoen skiftes ud med en fra M\u00e4rklin? Den skulle fylde lidt mindre i h\u00f8jden end Heljans egen. Det vil jeg dog ikke til at bakse med, s\u00e5 l\u00e6nge jeg bare kan k\u00f8re toget bagl\u00e6ns. I virkeligheden k\u00f8rer IC3 togene jo ogs\u00e5 i begge retninger.<\/p>\n\n\n\n Nu brokker jeg mig til forhandleren (nettog.dk). De plejer at svare hurtigt p\u00e5 e-mails.<\/p>\n\n\n\n 3 uger senere: Intet svar fra nettog.dk. Og jeg har endda rykket to eller tre gange. Yderst skuffende. M\u00e5ske skal man finde et andet sted at handle?<\/p>\n\n\n\n Lidt mere efterforskning, i pr\u00e6cis hvordan og hvorfor afsporingerne sker, endte med at sl\u00e6beskoen skilte sig ad p\u00e5 midten, alts\u00e5 at selve sl\u00e6beskoen faldt af, og kun \u201cfjederdelen\u201d blev tilbage p\u00e5 vognen. Jeg skubbede sl\u00e6beskoen tilbage p\u00e5 fjederen, og pludselig holdt afsporingsproblemerne op. Dog skal modsatte ende af toget m\u00e5ske have lidt mere v\u00e6gt for ogs\u00e5 at blive stabilt. Eller er det m\u00e5ske hjulafstanden, der skal justeres? Det siges, at M\u00e4rklin i gamle dage brugte 13,9 mm, mens der i NEM 340 normen st\u00e5r minimum 14,0.<\/p>\n\n\n Efter yderligere en uge – stadig uden svar fra nettog.dk – skulle toget \u201cluftes\u201d igen. Og nu afsporede sl\u00e6besko-enden igen. Derfor pillede jeg hjulene (og derfor sl\u00e6beskoen) af, for at justere hjulafstanden. Men det var ikke n\u00f8dvendigt. Heljan har allerede justeret til 13,95 mm. Efter at have samlet vognen igen var der stadigv\u00e6k problemer i et bestemt sporskifte. Som om sl\u00e6beskoen kiler sig fast. Problemet gik dog pludselig i sig igen, da jeg var i gang med at finde ud af pr\u00e6cis hvad der skete. Min teori er, at sl\u00e6beskoen p\u00e5 en eller anden m\u00e5de flytter sig en mm, hvorefter der ikke er plads til den. M\u00e5ske skal den udskiftes med en M\u00e4rklin sl\u00e6besko? En 7164 burde passe if\u00f8lge diverse indl\u00e6g p\u00e5 sporskiftet.dk<\/a>, hvor nogen har sat M\u00e4rklin sl\u00e6besko p\u00e5 andre Heljan modeller. Men hov: Togdillen har rent faktisk allerede sat en M\u00e4rklin sl\u00e6besko p\u00e5 mit \u201cgamle\u201d IC3 tog. Det havde jeg slet ikke bem\u00e6rket f\u00f8r nu. Men det er \u00e5benbart en v\u00e6sentlig del af at f\u00e5 et Heljan IC3 tog til at k\u00f8re ordentligt. Det m\u00e5 dog vente til n\u00e6ste vinters\u00e6son. F\u00f8rste billede viser mit nye tog med den originale Heljan sl\u00e6besko. N\u00e6ste billede er mit gamle tog med en M\u00e4rklin sl\u00e6besko:<\/p>\n\n\n\n I mellemtiden har Mck og Dekas meddelt, at de ogs\u00e5 vil lave et IC3 tog alligevel. Nu m\u00e5 vi se. Der g\u00e5r vel et par \u00e5r med at f\u00e5 det produceret. S\u00e5 der er tid til at spare sammen.<\/p>\n\n\n\n Jeg fik en henvendelse helt fra Australien om et godt fif til at f\u00e5 et Heljan IC3 tog til at holde op med at vrikke sig igennem sving og sporskifter, og dermed til at holde sig p\u00e5 sporet.<\/p>\n\n\n Jeffrey Lynn alias SRman i britiske modeltogskredse har gode erfaringer med at bore denne styretap p\u00e5 hver ende af midtervognen v\u00e6k: Men jeg tror stadig, at mit st\u00f8rste problem er sl\u00e6beskoen, som skal erstattes med en M\u00e4rklin.<\/p>\n","protected":false},"excerpt":{"rendered":" November 2nd 2014 Postscript: The following description is how I experienced it. There are a few harsh comments to both Heljan and Togdillen. But it ends somewhat more positive than it begins – especially regarding Togdillen. So please read the last part of the story. I was at Hobbymessen in Valbyhallen. Togdillen stood there with … Continue reading The Heljan IC3 Train<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-3779","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/pages\/3779"}],"collection":[{"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=3779"}],"version-history":[{"count":1,"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/pages\/3779\/revisions"}],"predecessor-version":[{"id":3783,"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/pages\/3779\/revisions\/3783"}],"wp:attachment":[{"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=3779"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\nNovember 3, 2014:<\/h2>\n\n\n\n
<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\nNovember 4, 2014:<\/h2>\n\n\n\n
November 5 – 14, 2014:<\/h2>\n\n\n\n
November 15, 2014:<\/h2>\n\n\n\n
<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\n
\n<\/p>\n\n\n<\/a><\/figure><\/div>\n\n\n
\n<\/p>\n\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\nMay 9, 2017<\/h2>\n\n\n\n
Marts 2020 – endnu et Heljan IC3 tog<\/h2>\n\n\n\n
<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n<\/a><\/figure><\/div>\n\n<\/a><\/figure><\/div>\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n<\/a><\/figure><\/div>\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n\n<\/a><\/figure><\/div>\n\n<\/a><\/figure><\/div>\n\n\nSommer 2020<\/h2>\n\n\n\n
<\/a><\/figure><\/div>\n\n<\/a><\/figure><\/div>\n\n\n
\n<\/a>og erstatte den med en skrue i stedet:<\/p>\n\n\n\n
![\n<\/a>og erstatte den med en skrue i stedet:<\/p>\n\n\n\nMen jeg tror stadig, at mit st\u00f8rste problem er sl\u00e6beskoen, som skal erstattes med en M\u00e4rklin.<\/p>\n","protected":false},"excerpt":{"rendered":"November 2nd 2014 Postscript: The following description is how I experienced it. There are a few harsh comments to both Heljan and Togdillen. But it ends somewhat more positive than it begins – especially regarding Togdillen. So please read the last part of the story. I was at Hobbymessen in Valbyhallen. Togdillen stood there with … Continue reading The Heljan IC3 Train<\/span><\/a><\/p>\n","protected":false},"author":1,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"footnotes":""},"class_list":["post-3779","page","type-page","status-publish","hentry"],"_links":{"self":[{"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/pages\/3779"}],"collection":[{"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=3779"}],"version-history":[{"count":1,"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/pages\/3779\/revisions"}],"predecessor-version":[{"id":3783,"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=\/wp\/v2\/pages\/3779\/revisions\/3783"}],"wp:attachment":[{"href":"https:\/\/lisby.dk\/wordpress\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=3779"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}](\"http:\/\/lisby.dk\/wordpress\/wp-content\/uploads\/2016\/10\/6FC02F4B-8EC0-48F0-A17D-691B224E5AA5.jpeg\"){kind=link}